Clear answers.
Before you book.

The price depends on the size of the pane, the type of safety glass, whether the hardware needs repair, and whether the job needs an after-hours board-up first. A small tempered panel costs far less than a full laminated storefront door. A free on-site estimate gives the exact price before any work starts.

Yes. A technician can clear the broken glass and cover the opening the same night, keeping the business secure until the new pane is ready. Most commercial door glass is cut to size, so the permanent glass usually goes in on a second visit.

Yes. Federal safety rules and building codes require safety glass in doors. Tempered glass breaks into small, dull pieces instead of sharp shards, and laminated glass holds together when it cracks. Every replacement pane we install is one of these two types.

In most cases, no. Tempered glass can't be patched once it cracks, and the damaged pane can give out without warning. Cracked door glass should be replaced, and the opening can be secured right away until the new pane arrives.

Repeat breaks usually point to the hardware, not the glass. A closer that lets the door slam, loose hinges, or a frame that has shifted all put stress on the pane. Fixing those parts during the glass repair stops the next crack before it starts.

Anyone searching for commercial door glass repair near me across D.C., Maryland, or Northern Virginia is in the right place. Crews cover Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Call to confirm coverage for a specific address.

The price depends on the hinge type, the door's weight, how many hinges need replacing, and whether the frame needs repair first. A standard butt hinge swap costs far less than fitting a heavy storefront door with a continuous hinge. A free on-site estimate gives the exact written price before any work begins.

Replacement is usually needed when the door has dropped on the latch side, rubs the frame at the top, or has screws that spin without tightening. A cracked or worn hinge knuckle is another clear sign. A squeak alone often needs only lubrication, which a technician can confirm during the estimate.

A continuous hinge runs the full height of the door and spreads the weight along the entire edge instead of three or four points. It suits heavy, high-traffic doors that keep sagging, such as aluminum storefronts and steel exits. Many can be fitted to the existing door and frame without replacing either one.

Yes, in most cases. Standard butt and spring hinges are carried on the van and swapped in one visit. Continuous hinges are cut to the door's height and fire-rated hinges must match the door's rating, which can mean a second visit. The estimate will say which applies.

If a door repaired by our technicians isn't closing, latching, or locking properly afterward, a technician returns to correct it at no extra charge. The guarantee covers the hinge work performed. Call to book, and the full terms are confirmed with the estimate.

Anyone searching for commercial door hinge replacement near me across D.C., Maryland, or Northern Virginia is in the right place. Crews cover Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Call to confirm coverage for a specific address.

Price depends on the type of operator, which part has failed, and whether the door ties into a lock or card reader. Replacing a wireless push button is a small job, while a new motor or a full operator swap takes more parts and time. The free door check ends with one set price before work begins.

The most common causes are a dead battery in a wireless button, a receiver that lost its signal, a switch on the operator set to off, or a worn-out motor. A locked door can also block the opener from moving. A technician can test each part and find the cause in one visit.

A door that won't close usually has a stuck button, a sensor picking up movement, or a switch set to hold-open. Sometimes the wait time is simply set too long. Most of these are quick fixes once a technician checks the system.

It's the type of opener found on most ADA doors. It opens slowly when someone presses a button or gives the door a light push, and it moves at a speed meant to avoid hurting anyone. These doors can still be opened by hand when the power goes out.

Yes. The lock and the opener need to be wired to work together, with the lock releasing a moment before the door starts to move. When they aren't set up this way, the opener fights the lock and wears out early.

Yes. Automatic door operator repair and installation is available near you in Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Share your address when you book, and we'll set a visit for your quietest hours.

Price depends on whether the closer is above the door or in the floor, how heavy the door is, and whether it needs hold-open or fire door features. A simple speed adjustment costs far less than replacing a floor closer under a heavy glass door. Your free door check ends with one fixed price before any work starts.

No. Oil leaking from a closer means the seals inside have failed, and refilling it won't hold. The closer needs to be replaced, and doing it soon protects your door, your glass, and the people walking through.

A slamming door usually means the closer is worn out, the speed setting got knocked out of place, or the closer is too weak for the door. Wind and air pressure inside the building can make it worse. A technician can find the cause and either reset the speed or replace the closer.

Overhead concealed closers usually fit inside the frame above aluminum storefront doors. Floor closers are common under heavy all-glass doors. The right one depends on how your door was built, which the technician checks during the free visit.

Yes. Many models can hold the door open once it's pushed past a set point, which helps during deliveries and busy hours. Fire doors are different and can only be held open by devices that release when the fire alarm goes off.

Yes. We repair and replace concealed door closers near you in Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Share your address when you book, and you'll get a visit time before or after business hours.

Cost comes down to the number of doors, battery or hardwired power, and whether the alarms link to a keypad or security panel. One battery exit alarm is a small job, while wiring several exits into one system takes more time and parts. The free walk-through ends with a set price you approve first.

No. An exit alarm makes noise when the door opens, but people can still push through and get out. Fire inspectors look for exits that are locked or chained shut, not ones that sound an alarm. Each alarm we fit is matched to that door's exit rules.

Yes. Most commercial door alarms come with a key or code that lets managers turn them off for deliveries or trash runs. Prop alarms can also be set to wait a few seconds or minutes before sounding, which gives a quick in-and-out time to finish quietly.

Battery alarms go up fast and suit single doors in smaller spaces. Hardwired alarms make more sense for buildings with several exits or a central security panel, since nobody has to remember battery changes. During the walk-through, the technician recommends a type for each door.

In most buildings, yes. Door contact sensors and alarmed exit hardware can link to the keypads, card readers, or security panels already in place. The technician checks your current setup during the visit and explains how the new alarms tie in.

Yes. Our technicians install and repair commercial door alarms near you across Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Share your address when you book, and we'll confirm the visit time.

Your total comes down to three things: how many doors get upgraded, whether you want one cylinder or a whole patented key system, and how many keys your team needs. A single back door is a quick, affordable job, while a building-wide system takes more planning and parts. You'll have a written number after the free review.

Two things working together. Tougher inside parts, like hardened pins and hidden extra locking pieces, slow down drills, picks, and bump keys. Patented keys stop copies from being made without permission. Many of these locks are tested to UL 437 or ANSI/BHMA A156.30.

Not without you. The key blanks aren't sold to hardware stores or kiosks, and authorized dealers ask to see the owner's authorization card before cutting a copy.

Usually. Many high-security cylinders drop into the locks and deadbolts you already have, keeping the job small. A lock too worn to protect anything gets flagged during the review, along with a replacement option.

Each key is tracked, letting you see right away which one is missing. A quick rekey shuts that key out, and replacements are cut through your authorization card while the rest of your doors stay locked.

Yes. We fit and service high-security locks near you throughout Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Pick a time outside your business hours, and a technician arrives ready to upgrade.

Audio stations for a single door are at the lower end. Video panels, tenant directories, and phone-answering systems cost more because of the equipment and wiring involved. The number of doors and whether existing cables can be reused also shape the total. A free on-site estimate lists the price for your entrance.

Often, yes. Many modern systems run on the two-wire or multi-wire cables already in the building, and some connect over the internet or a cellular signal instead. The technician tests the existing wires during the estimate to see what can stay.

Many current systems send the call to a phone app, letting you see the visitor, talk to them, and open the door from anywhere. This helps owners and managers who split their time between sites or aren't at the front desk all day.

The cause is usually the lock side, not the intercom. A worn electric strike, a failing power supply, or a loose release wire can stop the door from opening even when the call works fine. A technician tests each part to find where the signal stops.

A directory panel makes sense once a building has more than a few suites or units. Visitors scroll to a name or enter a code instead of guessing which button to press, and names can be updated when tenants move in or out.

Most commercial video panels include built-in lighting or night vision for clear faces after dark. Placement still matters, which is why cameras are angled away from glare and streetlights during install.

Yes. Commercial intercom installation and repair is available near you across Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Share your address when you book to confirm the visit.

Price depends on the keypad model, how many doors you want covered, and whether the door needs an electric strike or a new lock to work with it. A battery keypad on a single office door is a quick job, while a wired system across several entrances takes more parts. The free visit ends with a fixed price you approve.

Yes. A manager with the master code can remove a single user's code in under a minute, without changing anyone else's. The person who left loses access immediately, and the rest of your team keeps using their own codes as usual.

In most cases, yes. Many keypads replace the current lock on the same door, and others work with an electric strike or magnetic lock added to the frame. During the visit, a technician checks your door and lock and tells you which setup fits.

Some commercial keypads keep an entry log showing which code was used and at what time. This helps managers check late openings, early arrivals, and after-hours visits. If tracking matters to you, the technician will recommend a model with this feature.

Yes, when it's installed correctly. The keypad controls entry from outside, while the inside handle or push bar still opens the door instantly for anyone leaving. Our technicians set up each keypad door to keep the way out clear.

Yes. Keypad installs and repairs are available across Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Send your address when you book, and you'll get a confirmed visit window.

Cost depends on the lock's holding force, single or double doors, the power supply, and whether it ties into a card reader or fire alarm. A single interior door lock is a short job, while a double exterior entrance with backup power takes more parts and time. The free lock check ends with an itemized quote.

It releases. Magnetic locks need power to hold, so the door unlocks when the power drops, which keeps exits safe for people inside. A battery backup or a second mechanical lock on the outside keeps the building secure until power returns.

Yes, when they're installed to code. The lock must release from the inside through an exit button, sensor, or door hardware switch, and it must unlock on power loss. Many setups also need to release when the fire alarm sounds. Our technicians wire each lock to the rules for that door.

The most common causes are a magnet and plate that no longer meet flat, a loose mounting bracket, a dirty plate, or low power from a failing supply. A sagging door can also pull the plate out of line. A technician can realign the lock and test its full hold in one visit.

Yes. Mag locks connect to most card readers, keypads, fobs, and intercoms. The exit release still has to cut power to the lock on its own, so people can get out even if the access system goes down.

Yes. Our technicians install and fix commercial magnetic locks near you in Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Book a visit with your address, and you'll get a confirmed arrival time.

Track cleaning and sensor adjustments are at the lower end. New rollers, drive belts, and motors cost more because of the parts involved. Automatic sliders usually cost more to repair than manual ones. A free on-site estimate lists the exact parts and the total before any work starts.

The usual causes are worn rollers, dirt packed into the track, a bent bottom guide, or a stretched drive belt. On automatic doors, a power or sensor problem can also stop the door from moving. A technician can find the exact cause during one visit.

The sensor is likely picking up something other than people, like signs, hanging decorations, bugs, or traffic outside. Dirty or misaligned sensors can do the same. Cleaning and re-aiming the sensors usually stops the random opening.

Grinding or scraping usually means the rollers are worn or the panel has dropped low enough to drag along the bottom guide. Left alone, it wears grooves into the track and strains the motor. Replacing the rollers and leveling the panel ends the noise.

In most cases, yes. Rollers, tracks, belts, sensors, and locks can each be replaced on their own, which costs far less than a new door. Full replacement only makes sense when the frame or glass panels are badly damaged.

Many automatic sliders can be pushed open by hand, and most include breakout panels that swing outward for emergency exit. Some models also carry battery backup to keep running for a short time. A technician can check how yours is set up.

Yes. Manual and automatic sliding door repair is available near you across Washington, D.C., Montgomery and Prince George's counties, Arlington, Alexandria, and Fairfax County. Mention your door brand when you book if you know it, and the technician will bring the right parts.

Cost depends on whether the current device can take a retrofit kit or needs replacing with new ADA handicap exit devices. Power supplies, wiring runs, and fire-rated hardware add to the total. A door that already has an opener usually needs less work. A free on-site estimate gives the price for each door.

The 2010 ADA standards call for door hardware that works with one hand and without tight grasping or twisting, mounted between 34 and 48 inches. They also reference a 5-pound limit on operating force. The push side must stay smooth within 10 inches of the floor on most doors.

In most cases, the latch is still holding the door closed. The opener can’t pull a latched door open on its own. Electric latch retraction or an electric strike releases the latch first. A failed power supply or a loose wire can cause the same problem.

Yes, anyone searching for ADA exit device installation near me in D. C., Maryland, or Northern Virginia can book a visit with our technicians. The service area covers Washington, D. C., Montgomery and Prince George’s counties, Arlington, Alexandria, and Fairfax County. Call us to confirm an address.

On a non-rated door, yes, though the door stays unlocked until someone undogs it. Fire-rated doors can’t be dogged at all. Electric latch retraction solves both problems by releasing the latch only when the button is pressed.

The bottom rod often sits in the 10-inch zone that must stay smooth on the push side. Less bottom rod devices or concealed rods usually clear that zone. Some existing doors fall under exceptions, and a technician can check which applies.

Many popular exit devices accept a retrofit kit that adds electric latch retraction without replacing the whole device. Older or discontinued models may need a new device. The free estimate confirms which option fits each door.

Most of the price comes from the closer itself, followed by labor. A basic valve adjustment costs far less than a new heavy-duty or fire-rated closer. Arm style, door size, and any frame repair also affect the total. A free on-site estimate gives the exact price before work begins.

The sweep or latch speed is usually set too fast, or the closer has lost its oil. Wind against an exterior door can make it worse. Valve adjustment fixes the first case. A closer that has lost oil needs replacing, since no setting can slow the door without fluid inside.

No, the seals inside a commercial closer can’t be rebuilt on site. Lost fluid can’t be topped up either. Once oil shows on the body or arm, the closer is already losing control of the door, and replacing it is the safe fix.

Yes, anyone searching for commercial door closer repair near me in D. C., Maryland, or Northern Virginia can have a technician sent out. We work across Washington, D. C., Montgomery and Prince George’s counties, Arlington, Alexandria, and Fairfax County. Call us with the address to confirm a visit.

A latch speed set too slow is the most common cause. An undersized closer, a misaligned strike, or air pressure from wind or the HVAC system can also stop the door short. A technician can find the cause by watching the door through its last few inches of travel.

ADA standards limit interior, non-fire-rated doors on accessible routes to 5 pounds of opening force. Exterior doors have no federal ADA limit, though local codes may set one. Fire doors need enough closing power to latch reliably, so their settings follow the door’s listing.

A check twice a year works well for most buildings. Hydraulic fluid thickens in cold weather and thins in heat, which changes how fast the door closes. Busy entrances and exterior doors may need attention more often, especially after a hard winter.

The lever’s grade and function drive most of the price. A basic passage lever costs less than a keyed storeroom set or a vandal-resistant model. Finish, door thickness, and the number of doors also affect the total. A free on-site estimate lists the price for each door before any work starts.

A worn return spring inside the lever is the usual cause. Loose set screws and a worn spindle can add to the droop. Light-duty levers sag faster under business traffic, and a commercial-grade lever with independent springs holds its level position far longer.

On doors that must be accessible, ADA standards require hardware that works with one hand and without tight grasping, pinching, or twisting of the wrist. Round knobs generally fail that test, and levers meet it. Many businesses swap knobs for levers during remodels or after an accessibility review.

Yes, anyone searching for commercial door handle repair near me in D. C., Maryland, or Northern Virginia can book a visit with our technicians. The service area includes Washington, D. C., Montgomery and Prince George’s counties, Arlington, Alexandria, and Fairfax County. Call us to confirm a specific address.

Both are commercial grades, but Grade 1 passes tougher durability and strength tests. Grade 1 suits main entrances, schools, and doors that see constant use. Grade 2 fits lighter office and interior doors. Grade 3 is residential hardware and isn’t built for business traffic.

A vandal-resistant lever uses a clutch that lets the outside handle turn freely when the door is locked. Forcing it doesn’t break the lock inside. This design protects storefronts, restrooms, and back doors where someone might hang on or kick the lever.

ADA standards place door hardware on accessible doors between 34 and 48 inches above the finished floor. Most commercial levers sit near the middle of that range. Replacement levers usually reuse the existing door prep and stay at the same height.

Wall and floor stops sit at the lower end. Overhead stops and magnetic holders cost more because they need framework or wiring. The number of doors and the type of wall or floor also shape the total. A free on-site estimate lists the price for each door.

It depends on what sits behind the door. Floor stops suit most interior doors on hard floors. Wall stops work where solid backing sits behind the lever. Overhead stops fit exterior doors and openings with no wall or safe floor spot nearby.

Yes, but only with listed holders that release when the fire alarm sounds. Magnetic holders and closer-holder units are the common choices. Wedges, kick-down holders, and hooks are not allowed on fire doors because they stop the door from closing on its own.

Yes, anyone searching for commercial door stop installation near me in D. C., Maryland, or Northern Virginia can schedule a visit with our team. We cover Washington, D. C., Montgomery and Prince George’s counties, Arlington, Alexandria, and Fairfax County. Call us to confirm a specific address.

Either the door has no stop, or the stop sits on hollow drywall with nothing solid behind it. Each hard swing pushes the stop or lever deeper into the wall. A floor stop or a wall stop mounted over solid backing ends the damage.

Most exterior doors benefit from an overhead stop or a heavy-duty floor stop. Wind can swing an exterior door hard enough to bend the closer arm or tear the hinges. A stop that catches the door before that point protects the whole opening.

Most commercial hardware pros avoid them on heavy doors. A hinge pin stop catches the door right at the hinge, where the force works against the hinge and jamb. Floor, wall, and overhead stops catch the door farther out and spread the load better.

A latch or return spring replacement sits at the low end of the range. Fire-rated, alarmed, and mortise devices cost more to repair or replace. Outside trim and strike work add to the total as well. A free on-site estimate puts the exact price in writing before any work starts.

Many times the device is still dogged from earlier in the day. A broken return spring, a worn latch bolt, or a strike that shifted out of line can also stop the latch from catching. A technician can pinpoint the cause during one visit and fix it on the spot in most cases.

Dogging holds the push bar and latch in the retracted position. The door then swings freely without latching during busy open hours. It works with a hex key or a small key cylinder. Fire exit hardware is built without dogging because fire doors must latch every time they close.

Yes, businesses looking for commercial exit device repair near me in D. C., Maryland, or Northern Virginia can book our technicians directly. The service area covers Washington, D. C., Montgomery and Prince George’s counties, Arlington, Alexandria, and Fairfax County. Call us to check a specific address.

Yes, an exit device with electric latch retraction pulls the latch back when a card reader, keypad, or timer sends a signal. The door can stay unlocked during business hours and lock on its own at closing. The push bar still works normally from the inside at all times.

No, the code ties panic hardware to how a space is used. Under the International Building Code, assembly and educational spaces with 50 or more occupants need it, along with high-hazard areas. Many offices and stores still choose exit devices because they hold up well under heavy daily use.

A rim exit device mounts on the face of the door and latches into a strike on the frame. Most single commercial doors use this type. A mortise exit device works with a lock body set into a pocket in the door edge. That design looks cleaner and latches more securely, though it takes more work to install.

Handle length, material, and the type of door set make up most of the price. A stainless pull on a hollow metal door costs less than a back-to-back pull set for glass. Through-bolting and plate sets add to the total. A free on-site estimate gives the exact cost for each door.

Most loose pulls are held by surface screws that bite into thin aluminum or hollow metal. Each pull works them looser and widens the holes. Through-bolting the handle to hardware on the other side of the door holds it firm for good.

Yes, glass doors use back-to-back pulls joined by bolts through the glass, with sleeves and washers protecting each hole. The new pull has to match the existing holes, since tempered glass can’t be drilled once it’s made. A technician measures the hole spacing before ordering.

Yes, businesses searching for commercial push handle repair near me in D. C., Maryland, or Northern Virginia can request a visit from our team. The service area covers Washington, D. C., Montgomery and Prince George’s counties, Arlington, Alexandria, and Fairfax County. Call us to confirm your address.

A push plate is a flat panel mounted on the push side of a non-latching door. It protects the door face from hands and scuffs. A push bar runs across the door, often on storefront glass doors, and gives people a larger area to push, even with full hands.

A flat plate works best on the push side. People instinctively grab and pull any handle they see, which slows traffic at the entrance. Keeping handles on the pull side and plates or bars on the push side shows the right direction without a sign.

An offset pull bends away from the door at its mounting points. That shape keeps the grip clear of a lock cylinder or thumbturn mounted in the same spot. Offset pulls are common on storefront doors with a key lock near the handle.

Cost comes down to whether the device is surface or concealed, which parts have failed, the door’s fire rating, and the condition of the floor strike. A simple rod adjustment costs far less than replacing a concealed device built into the door. A free on-site estimate gives a written price before any work begins.

In most cases, the top latch is no longer holding in its open position. Without that hold, the bottom rod drops and scrapes while the door swings. A rod set too short, a worn top latch, or a damaged center case is usually behind it. Fixing that part stops the scraping.

Yes, on many doors. Removing the bottom rod and floor strike ends floor damage, clogged strikes, and tripping points. This option suits interior and cross-corridor pairs best, since exterior doors gain extra security from the bottom latch. Fire-rated doors typically need a fire pin and a listing that allows the change.

Businesses searching for vertical rod exit device repair near me in D. C., Maryland, or Northern Virginia can reach our technicians day or night. We cover Washington, D. C., Montgomery and Prince George’s counties, Arlington, Alexandria, and Fairfax County. Call us to confirm service at a specific address.

Surface rods mount on the face of the door, where they are easy to reach and adjust. Concealed rods run inside the door for a cleaner look, though they are harder to service and slip out of adjustment more easily. Both styles latch the door at the top and bottom.

No, fire exit hardware has to latch every time the door closes. That rule is why fire-rated devices come without dogging. Doors that need to stay open during business hours can use approved hold-open devices that release the door when the fire alarm sounds.